Installing a Transom Swim Platform

Installing a Transom Swim Platform

Installing a swim platform
Whenever someone uses the transom platform and boarding ladder, be sure to shut off the engine and detach the emergency shut-off switch clip to prevent the engine from inadvertently starting up. Tim Barker

Special deliverySign up for the free Boating email newsletter. Subscribe to Boating magazine for $14 for 1 year and receive 4 bonus digital issues.

Today, new boats are required to meet American Boat and Yacht Council Standard H-41 to provide (and I am paraphrasing here) a means of unassisted reboarding that is accessible to and deployable by a person in the water. 

For safety, this makes a lot of sense, particularly if a boater falls overboard from a vessel with tall gunwales that make it impossible to clamber back over the side. Instead, he or she can deploy a boarding ladder or other reboarding system to climb back in the boat more easily. 

However, a fair number of boats on the water today were built before the establishment of ABYC Standard H-41 in 2014; thus, some older vessels—particularly outboard boats with cutout transoms—might not meet this requirement.

To be clear, this is not a legal requirement on older boats, but it is a good idea. Fortunately, there are ways to add compliant reboarding systems, and one of the most popular for outboard-powered boats is the Garelick model 19536 transom platform with a telescoping, two-step stainless-steel boarding ladder. 

The ladder retracts to stow under the 18-inch-wide-by-15-inch-long polyethylene platform and is secured with a snap on a web strap. To deploy, the swimmer unsnaps the strap, pulls out and folds down the ladder, then uses the handhold and ladder to step up and into the boat. Here’s how to install this boarding system on an outboard-powered boat with an older-style cutout transom.

Skill Level: 2.5 of 5

Finish Time: Approx. 2-3 hours

Tools and Supplies

  • Garelick model 19536 transom platform with boarding ladder ($297.88; fisheriessupply.com)
  • 1/4-inch aluminum plate or 3/4-inch King Starboard to create a backing plate
  • Stainless-steel hardware for through-bolting the platform to the transom
  • Power drill and drill-bit set
  • Screwdriver and wrench set
  • Assembly lube
  • Marking pencil or masking tape
  • Marine sealant
Gathering the swim platform pieces
Assemble the Swim Platform Parts Tim Barker

Determine which side of the transom is most suitable for the platform. Using the supplied stainless-steel hardware, pre-drilled holes and assembly instructions, assemble the platform with the handrail to the outside edge of the platform and the lower support strut to the inside edge of the platform. Tighten the hardware securely and ensure that nothing is loose or wobbly before moving to the next step. To make mounting the platform a bit easier in step three, hold off on installing the boarding ladder assembly until after the boarding platform has been secured to the transom.

Marking the transom for installation
Mark the Location of the Swim Platform Tim Barker

To ensure clearance from the outboard, use the steering wheel to swing the motor as far as possible to the side on which you plan to install the platform. Then draw a line indicating the motor’s full extension. Position the platform assembly away from the line, ensuring that the platform itself is parallel to the waterline and about 3 to 4 inches above it. Mark the four mounting holes through the flattened ends (two each for the handrail and strut). Ensure that there are not wires, hoses or objects behind the mounting hole locations that might be damaged from drilling.

Drilling the transom
Install the Swim Platform Tim Barker

Drill the four marked holes with a bit compatible with the selected stainless-steel fasteners (not provided). Hold the drill perpendicular to the transom when drilling. If the transom is less than 2 inches thick, install a backing plate made of aluminum, marine plywood or King Starboard on the inside of the transom. Bed the mounting holes with marine sealant, then through-bolt each of the mounting points with at least a 1/4-inch stainless-steel bolt, washer (on the outside), fender washer (on the inside) and a nylon-locking nut. Tighten each fastener securely.

Installing the swim platform
Add the Ladder Tim Barker

Garelick offers a few ladder options for this platform, including versions that mount on top or under the platform. The 19536 has a two-step stainless-steel telescoping ladder that mounts underneath, and this configuration eliminates brackets and protrusions (and potential skinned knees) on the top surface of the platform. Use the supplied hardware, pre-drilled holes, stainless-steel hardware and instructions to securely mount the boarding ladder under the platform. Afterward, deploy and retract it to make sure it works smoothly and easily.

Read Next: More DIY Projects

Maintaining the swim platform
Maintain the Swim Platform Tim Barker

Garelick’s model 19536 transom platform and boarding ladder are constructed from corrosion-resistant materials, but salt water can lead to minor corrosion of the stainless-steel components. To keep the boarding platform and ladder in the best possible condition and operating smoothly, wash everything with fresh water and soap after each trip, and occasionally apply metal cleaner and polish to help maintain the luster of the stainless rails. Also, periodically check the mounting hardware for looseness and retighten if necessary.

The post Installing a Transom Swim Platform appeared first on Boating Mag.

Source: https://www.boatingmag.com/how-to/installing-a-transom-swim-platform/

Boat Lyfe